Tag: settings (page 2 of 2)

Simplify3D Version 4 – Improved Sequential Printing & Drag n Drop Reordering

The third video in my series on the changes in Version 4 of Simplify3D runs through the added functionality to use multiple processes on multiple parts when printing them one after the other, sequentially.

This feature will greatly assist those that sequentially print multiple parts that need their own individual split processes.

I also show the new feature in Version 4 which allows you to simply drag and drop the order in which the split processes are printed. If you got this wrong in previous versions it meant having to delete them all, starting again and creating them in a certain order. This too is a great time saver.

Find Simplify3D here.

Simplify3D Version 4 – What’s New, Part 2 – Seamless Process Transition

In this second video covering the updates included with version 4 of Simplify3D; I take a look at the new feature called “Seamless Process Transitions”.  (First part of this video series can be found here)

This features aims to remove any artifacts, or Z scars, from a print at the point of transition between two processes.

Before version 4 Simplify3D would insert solid layers between two different print settings in the same print, which could be visible in the resulting part.

I have a look at the theory and print out some tests in both version 3 and 4 to see what improvements are seen.

I had quite a fun time trying to get any differences to show up in photographs even though I used quite a high quality macro lens, nevertheless the photographs showing the difference between version 3 & 4 are below.

Simplify3D V3 Process Transition

Simplify3D V3 Process Transition

Simplify3D V4 "Seamless Process Transition"

Simplify3D V4 “Seamless Process Transition”

Here is a link to Simplify3D’s website.

Simplify3D Version 4 – What’s New, Part 1 – Variable Print Settings, Process Preview & Position Readout

A while ago I decided to use Simplify3D as my every day slicer and as a new version, version 4, was recently released I thought I would have a good look at what advantages and new features this version brings.

I had a search around on YouTube and found a few videos all talking about pretty much one feature – the variable print settings. I wanted to see if there was more to Version 4 than that, so I visited the Simplify3D website and dug into all of the changes in the latest release.

As I plan to try out all the new aspects to version 4 (where possible), I thought I would make a short series of videos showing these changes. I will cover all the new features and changes listed on their website and, where it makes sense, combine associated functionality into a single video.

This is the first of these videos. In this one I discuss the “Variable Print Settings” feature, which I see as more of a refinement of functionality already in version 3. This is the one feature being discussed most often that I see in other peoples’ discussions on version 4 but I wanted to find out if it truly does something you couldn’t do in previous versions…spoiler – it doesn’t 😉

While doing the Variable Print Settings it made sense to also cover two other new features in version 4, “Preview Your Processes” and “Position Readout”. So I detail these too in this video.

The temperature tower model I use in this video can be found on Thingiverse, here.

First ABS Print on DIY Prusa i3 MK2 – Slicer Settings, Test Prints & Results

After banging on about it for months, I finally get around to trying ABS filament on my DIY Prusa. I heard lots of bad things about trying to print ABS, especially without an enclosure, so I was ready for the worst. Expectations were set low 😉

In this video I go through, in quite a lot of detail (!), my initial slicer settings, run some test prints and think about the results….

RepRap Prusa i3 MK2 – One Week In, More Prints & Settings

In this video I go through some of the prints I have made in the first week after building the DIY Prusa i3 MK2, and some of the interim conclusions I have drawn from them together with the settings this had led me to change.

Long story short; it is quite hard to diagnose a lot of issues as they could be caused by a number of different things  manifesting with the same symptoms. It maybe even a combination. I had to single out settings and go wild with them to see what effect they had and then apply that to my baseline. However, apart from filament getting stuck on the spool (my fault) I haven’t had any failures and all the prints have been perfectly fit for the job I needed them for. So really we are only looking at aesthetics.

I also gave Simplify3D a try out…. at this time I don’t really need any of the capabilities it has over Slic3r and found it to exhibit some unwanted artifacts on the prints I tried it out on. It is a little disappointing that they offer no free trial as it isn’t particularly cheap and is very much a piece of software you will either get on with or you wont. You have to first spend your money to find out… You can apparently get a refund though if it doesn’t turn out well. For the time being I am sticking with Slic3r as I get better quality prints and really the only feature I would use right now from S3D is the manual supports.

I have decided to make Octoprint my next upgrade as for the time being the electronics are holding together just fine. So on with that!!!

Newer posts

© 2020 Jules Gilson

 

Additional Artwork Designed by Freepik Additional Artwork Designed by Freepik