Arduino Power Controller for Prusa 3D Printer – Auto Shutdown

https://youtu.be/UT9hDOvRGq0 In this video I run through the design and build of an add-on for my DIY Prusa i3 MK2 ...
Read More

Prusa i3 MK2 3D Printer – Electronics Mounted, FINALLY!

https://youtu.be/LxpDxNsQYv0 In this video I show how I ended up mounting all the electronics for the Prusa i3 MK2 clone ...
Read More

Fixing LCD Corruption on Prusa i3 MK2 Clone with RAMPS & Arduino

https://youtu.be/MbnSDWP23cA Really the only part of my Prusa i3 MK2 clone build that didn't function as it should out of ...
Read More

Prusa i3 MK2 3D Printer – Electrical Upgrades/Mods – RAMPS & Arduino

https://youtu.be/ewqIKWYJ6vc Continuing with my mission this week to actually finish the electrics on my DIY Prusa i3 MK2 3D Printer, ...
Read More

Prusa i3 MK2 Clone – Electronics – 24V Heated Bed Upgrade

https://www.youtube.com/watch?v=USbnLrTnWPQ I have changed my mind a few times about how I plan to finish off my Prusa i3 MK2 ...
Read More

How to Setup OctoPrint Guide – The Easy Way, OctoPi Tutorial

https://youtu.be/0TNH0g2WvAc Up till now I have been using an old laptop to connect to the 3D printer through Pronterface. While ...
Read More

RepRap Prusa i3 MK2 – One Week In, More Prints & Settings

https://youtu.be/I8TLEiClwGc In this video I go through some of the prints I have made in the first week after building ...
Read More

RepRap Prusa i3 First Print Analysis, Adjustments & Second Print

https://www.youtube.com/watch?v=l3wehsH_Sew Well after the failure of the first print I was kind of pleased!!! Until it failed it was printing way ...
Read More

How to Build a Cheap Prusa I3 MK2 3D Printer – Power Supply, Slicing & First Print!!

https://youtu.be/p0F1LBqI8oA In this video I finally get to make the first print... I know how it turned out but you ...
Read More

Reprap / Prusa 3D Printer – Complete Initial Setup & Configuration – Step by Step

https://youtu.be/cfIovRg5pLI Bit of a monster video, for me, at nearly an hour. It is compacted as much as possible but there ...
Read More

How to Build a Cheap Prusa I3 MK2 3D Printer – Arduino Check & Marlin Config

https://www.youtube.com/watch?v=27WOV4PXmTE So before getting all carried away and wiring in the Arduino and RAMPS I thought it might be a ...
Read More

How to Build a Cheap Prusa I3 MK2 3D Printer – Heated Bed

https://youtu.be/ljoBhZf3BoM I am starting to shift away from the Prusa build manual now as I move into the parts which ...
Read More

Extruder Gear Misalignment on Prusa i3 MK2 Build

https://youtu.be/bUWhjwU3Ujw As I mentioned in the last post, after building up the extruder/hot end assembly I tried to feed some ...
Read More

How to Build a Cheap Prusa I3 MK2 3D Printer – Building Z Axis & Extruder

https://youtu.be/8PQtjgcIjkQ Aside of being careful to keep everything lined up, parallel & square the build of the Z Axis, mounting ...
Read More

How to Build a Cheap Prusa I3 MK2 3D Printer – Building the X Axis

https://youtu.be/HQCHdaZNAuI I thought this part was going to be simple - all pretty much in line with the Original Prusa ...
Read More

How to Build a Cheap Prusa I3 MK2 3D Printer – Schoolboy Error #1 Y Corners

https://youtu.be/9j8BuP8WQoE In the last video I noted I could't work out how the Y limit switches fitted. In the course ...
Read More

How to Build a Cheap Prusa I3 MK2 3D Printer – The Y Axis

https://www.youtube.com/watch?v=EowZGVRTreQ So the build begins (finally). Luckily when running through the parts in part 1 of the series I noticed ...
Read More

A Better Prusa i3 Frame Template?

https://www.youtube.com/watch?v=-RjfNBCjFmc I decided to get on and cut the frame out first - made from two identical pieces of 12mm ...
Read More

How to Build a Cheap Prusa I3 MK2 3D Printer – Intro & Parts

https://youtu.be/lz9LnVQEomw This is the first of a few videos that I will be making over the next week or so, ...
Read More