Month: August 2017

Simplify3D Version 4 – Strong Foundations – Improved Support Structures

In this video I try out what Simplify3D refer to on their website as “Strong Foundations”. What this actually means is that in version 4 they have added a couple of new settings to improve the bed adhesion and overall strength of support material.

I look at what these new settings do and what that could mean for support structures – especially if you have ever had issues with the supports lifting off the printer bed.

Find Simplify3D here

Simplify3D Version 4 – Variable Extrusion Sizing & Dynamic Gap Fill

In the fourth video showing the changes in Simplify3D I look at two new features that both rely on one main change – the ability for Simplify3D to attempt varying the extrusion width dynamically.

The first feature, “Variable Extrusion Sizing”, permits you to attempt to print features that might otherwise just not print at all, where the total feature size is very small. I demonstrate that this works to very good effect.

The second feature, “Dynamic Gap Fill”, comes in very handy where you have features that in the past left gaps between perimeters and infill, or between two perimeters on very small features. It fills in these gaps with filament which is extruded at a smaller width that your general settings allow.

Find Simplify3D here

Simplify3D Version 4 – Improved Sequential Printing & Drag n Drop Reordering

The third video in my series on the changes in Version 4 of Simplify3D runs through the added functionality to use multiple processes on multiple parts when printing them one after the other, sequentially.

This feature will greatly assist those that sequentially print multiple parts that need their own individual split processes.

I also show the new feature in Version 4 which allows you to simply drag and drop the order in which the split processes are printed. If you got this wrong in previous versions it meant having to delete them all, starting again and creating them in a certain order. This too is a great time saver.

Find Simplify3D here.

Simplify3D Version 4 – What’s New, Part 2 – Seamless Process Transition

In this second video covering the updates included with version 4 of Simplify3D; I take a look at the new feature called “Seamless Process Transitions”.  (First part of this video series can be found here)

This features aims to remove any artifacts, or Z scars, from a print at the point of transition between two processes.

Before version 4 Simplify3D would insert solid layers between two different print settings in the same print, which could be visible in the resulting part.

I have a look at the theory and print out some tests in both version 3 and 4 to see what improvements are seen.

I had quite a fun time trying to get any differences to show up in photographs even though I used quite a high quality macro lens, nevertheless the photographs showing the difference between version 3 & 4 are below.

Simplify3D V3 Process Transition

Simplify3D V3 Process Transition

Simplify3D V4 "Seamless Process Transition"

Simplify3D V4 “Seamless Process Transition”

Here is a link to Simplify3D’s website.

Simplify3D Version 4 – What’s New, Part 1 – Variable Print Settings, Process Preview & Position Readout

A while ago I decided to use Simplify3D as my every day slicer and as a new version, version 4, was recently released I thought I would have a good look at what advantages and new features this version brings.

I had a search around on YouTube and found a few videos all talking about pretty much one feature – the variable print settings. I wanted to see if there was more to Version 4 than that, so I visited the Simplify3D website and dug into all of the changes in the latest release.

As I plan to try out all the new aspects to version 4 (where possible), I thought I would make a short series of videos showing these changes. I will cover all the new features and changes listed on their website and, where it makes sense, combine associated functionality into a single video.

This is the first of these videos. In this one I discuss the “Variable Print Settings” feature, which I see as more of a refinement of functionality already in version 3. This is the one feature being discussed most often that I see in other peoples’ discussions on version 4 but I wanted to find out if it truly does something you couldn’t do in previous versions…spoiler – it doesn’t 😉

While doing the Variable Print Settings it made sense to also cover two other new features in version 4, “Preview Your Processes” and “Position Readout”. So I detail these too in this video.

The temperature tower model I use in this video can be found on Thingiverse, here.

Practical Uses of a 3D Printer – Printing a Nipple

Now I don’t really use my 3D printer for anything decorative – and there are plenty of videos out there if that’s what you want to see. So I thought I would occasionally put up a video showing how I use the 3D printer for more practical purposes. This is the first of those – hopefully future parts will be a little more interesting!!

In this video I make a nipple to fix a vacuum reservoir – showing the issue, the design, the slicing and the print. Then fixing the new part in place, repairing the item.

© 2017 Jules Gilson

 

Additional Artwork Designed by Freepik Additional Artwork Designed by Freepik