Cheap DIY Prusa i3 MK2 Build

Arduino Power Controller for Prusa 3D Printer – Auto Shutdown
In this video I run through the design and build of an add-on for my DIY Prusa i3 MK2 3D ...
Read More
Read More

Prusa i3 MK2 3D Printer – Electronics Mounted, FINALLY!
In this video I show how I ended up mounting all the electronics for the Prusa i3 MK2 clone. As ...
Read More
Read More

Fixing LCD Corruption on Prusa i3 MK2 Clone with RAMPS & Arduino
Really the only part of my Prusa i3 MK2 clone build that didn't function as it should out of the ...
Read More
Read More

Prusa i3 MK2 3D Printer – Electrical Upgrades/Mods – RAMPS & Arduino
Continuing with my mission this week to actually finish the electrics on my DIY Prusa i3 MK2 3D Printer, in ...
Read More
Read More

Prusa i3 MK2 Clone – Electronics – 24V Heated Bed Upgrade
I have changed my mind a few times about how I plan to finish off my Prusa i3 MK2 clone ...
Read More
Read More

How to Setup OctoPrint Guide – The Easy Way, OctoPi Tutorial
Up till now I have been using an old laptop to connect to the 3D printer through Pronterface. While this ...
Read More
Read More

RepRap Prusa i3 MK2 – One Week In, More Prints & Settings
In this video I go through some of the prints I have made in the first week after building the ...
Read More
Read More

RepRap Prusa i3 First Print Analysis, Adjustments & Second Print
Well after the failure of the first print I was kind of pleased!!! Until it failed it was printing way better ...
Read More
Read More

How to Build a Cheap Prusa I3 MK2 3D Printer – Power Supply, Slicing & First Print!!
In this video I finally get to make the first print... I know how it turned out but you will ...
Read More
Read More

Reprap / Prusa 3D Printer – Complete Initial Setup & Configuration – Step by Step
Bit of a monster video, for me, at nearly an hour. It is compacted as much as possible but there is ...
Read More
Read More

How to Build a Cheap Prusa I3 MK2 3D Printer – Arduino Check & Marlin Config
So before getting all carried away and wiring in the Arduino and RAMPS I thought it might be a good ...
Read More
Read More

How to Build a Cheap Prusa I3 MK2 3D Printer – Heated Bed
I am starting to shift away from the Prusa build manual now as I move into the parts which are ...
Read More
Read More

Extruder Gear Misalignment on Prusa i3 MK2 Build
As I mentioned in the last post, after building up the extruder/hot end assembly I tried to feed some filament ...
Read More
Read More

How to Build a Cheap Prusa I3 MK2 3D Printer – Building Z Axis & Extruder
Aside of being careful to keep everything lined up, parallel & square the build of the Z Axis, mounting the ...
Read More
Read More

How to Build a Cheap Prusa I3 MK2 3D Printer – Building the X Axis
I thought this part was going to be simple - all pretty much in line with the Original Prusa Build ...
Read More
Read More

How to Build a Cheap Prusa I3 MK2 3D Printer – Schoolboy Error #1 Y Corners
In the last video I noted I could't work out how the Y limit switches fitted. In the course of ...
Read More
Read More

How to Build a Cheap Prusa I3 MK2 3D Printer – The Y Axis
So the build begins (finally). Luckily when running through the parts in part 1 of the series I noticed I ...
Read More
Read More

A Better Prusa i3 Frame Template?
I decided to get on and cut the frame out first - made from two identical pieces of 12mm plywood ...
Read More
Read More

How to Build a Cheap Prusa I3 MK2 3D Printer – Intro & Parts
This is the first of a few videos that I will be making over the next week or so, covering ...
Read More
Read More